CN Crane Licence Course – 4 days – Melbourne

If you’re looking to complete your CN crane course in Melbourne, Go Workplace Training delivers nationally recognised, WorkSafe-approved training at our purpose-built facility in Dandenong South. Our CN crane licence course covers everything you need to safely operate a non-slewing mobile crane with a capacity greater than 3 tonnes, including Franna pick-and-carry cranes, articulated mobile cranes, reach stackers, and non-slewing telehandlers.

Whether you’re new to crane operation or formalising existing skills with a nationally recognised unit of competency, our 4-day crane operator course in Victoria provides the hands-on training and the unit of competency required to apply for your WorkSafe High Risk Work Licence Class CN.

Go Workplace Training is one of Victoria’s most established Registered Training Organisations (RTO 22464), with over 20 years delivering high-risk work licence training across construction, civil, logistics, mining, and industrial industries.

The CN crane licence is a WorkSafe High Risk Work Licence (HRWL) that authorises the holder to operate a non-slewing mobile crane with a capacity greater than 3 tonnes. It is a legal requirement under the Occupational Health and Safety Act and Regulations (OHS) legislation that anyone operating this class of crane on an Australian worksite must hold a current and valid licence.

The unit of competency behind the CN licence is TLILIC0040 Licence to operate a non-slewing mobile crane (greater than 3 tonnes capacity). This unit is assessed by your Registered Training Organisation (Go Workplace Training) and by a WorkSafe-approved assessor before your licence is issued.

The CN licence allows you to operate:

• Non-slewing mobile cranes (greater than 3 tonnes capacity)
• Reach stackers
• Non-slewing telehandlers

The CN is the licence you need if you operate a Franna crane, a pick-and-carry crane, an articulated mobile crane, or similar equipment on construction sites, in logistics, or across industrial settings throughout Victoria.

CN vs C6: what’s the difference? The C6 licence covers slewing mobile cranes (cranes that rotate 360 degrees) with a capacity of up to 60 tonnes. The CN covers non-slewing mobile cranes, which cannot rotate but instead luff (up/down) or telescope (in/out). These are fundamentally different types of equipment requiring different licences. If you operate both types, you will need both licences.

Our CN crane course in Melbourne is delivered over 4 days at our Dandenong South training facility, located at 16 Kitchen Road, Dandenong South VIC 3175, easily accessible from Melbourne’s south-east and greater metropolitan area.

The course combines pre-study and homework completed before your face-to-face training days, so that class time is focused on hands-on, practical crane operation. A key component of the CN course is learning to drive articulated mobile cranes, including operating them through an obstacle course on private roads or property to simulate real worksite conditions.

Our trainers are experienced crane operators and qualified workplace assessors who bring practical industry knowledge to every session.

Course snapshot:

• Unit: TLILIC0040 Licence to operate a non-slewing mobile crane (greater than 3 tonnes capacity)
• Licence Class: CN Non-slewing mobile crane (greater than 3 tonnes)
• Duration: 4 days (includes some pre-study and homework followed by 4-days face to face sessions with us)
• Location: Dandenong South, Melbourne VIC
• Delivery: Pre-study + Face-to-face, practical training
• RTO: Go Workplace Training (RTO 22464)
• Outcome: Unit Statement of Attainment + WorkSafe High Risk Work Licence (CN)

Course fees:

• Individual/private booking: $2,200 per student (deposit of $1,499 required, balance of $701 due on Day 1)
• Company booking (1–3 students): $2,200 per student
• Company booking (4+ students): $2,100 per student

WorkSafe licence fees are paid separately via the MyWorkSafe portal or at Australia Post after successful completion of your assessment.

If the standard 4-day format doesn’t suit your schedule, talk to us and we may be able to explore weekend or customised delivery options depending on availability.

A non-slewing mobile crane is a mobile crane whose boom or jib cannot rotate (slew) around a vertical axis. Instead of slewing, the boom can luff (move up and down) or telescope (extend and retract). This is the defining characteristic that separates non-slewing cranes from slewing cranes like the C6 class.

Non-slewing mobile cranes include:

• Articulated mobile cranes (commonly known as Franna cranes or pick-and-carry cranes)
• Locomotive mobile cranes

Non-slewing mobile cranes do not include:

• Vehicle tow trucks or cranes mounted on tow trucks

The Franna crane is the most common type of non-slewing mobile crane used on construction and industrial sites in Victoria. Frannas are highly versatile, capable of travelling with a suspended load (pick-and-carry), and are widely used in situations where a stationary crane would be impractical due to site layout or access constraints.

Driving on public roads: Completing the CN crane course and holding a CN licence does not authorise you to drive an articulated mobile crane on a public road. Driving a Franna or similar machine on a main road requires a valid heavy vehicle licence issued by the relevant transport regulator. The CN licence covers worksite operation only.

The CN crane operator course in Victoria is designed for both new entrants to crane operation and experienced operators who need to formalise their skills with a nationally recognised licence.

This course is ideal for:

• Construction site workers who regularly work with Franna or pick-and-carry cranes
• Riggers and doggers looking to expand into crane operation
• Civil construction workers who need to operate articulated mobile cranes on infrastructure or road projects
• Logistics, warehousing, and heavy transport workers using reach stackers or non-slewing telehandlers
• Mining and resources workers who require a CN licence as part of a site entry or employment requirement
• Business owners or site managers looking to upskill their team with a qualified CN crane operator

The CN licence is one of the most in-demand crane unit on Victorian worksites. Franna cranes in particular are a staple of commercial construction, and most project sites require operators to hold a current licence before touching the equipment. Completing your crane licence course near you in Melbourne puts you on the shortest path to site-ready course.

The CN crane course covers the full range of competencies required to safely operate a non-slewing mobile crane in a commercial worksite environment. Training is structured around the requirements of the unit of competency and WorkSafe Victoria’s High Risk Work Licence assessment standards.

Course topics include:

• Planning and preparing for crane work, including site assessment and lift planning
• Pre-operational safety checks and equipment inspection procedures
• Reading and interpreting load charts to calculate safe working loads
• Selecting the appropriate crane configuration and lifting gear for the task
• Identifying hazards in the work area and applying appropriate risk controls
• Setting up the crane correctly for safe operation
• Driving an articulated mobile crane on private roads and property, including through an obstacle course
• Driving without a load and manoeuvring the crane through constrained environments
• Lifting, moving, and placing loads safely using correct techniques
• Using hand signals and two-way radio communication with doggers and riggers on the ground
• Working with different load types, including awkward and asymmetric loads
• Following OHS legislative requirements and WorkSafe Victoria regulatory standards
• Responding to equipment problems, mechanical issues, or unexpected site conditions
• Parking and shutting down the crane properly at the end of operations

By the end of the course (at the successful completion of the course requirements including assessments), you will have the practical skills and theoretical knowledge to confidently and safely operate non-slewing mobile cranes and the course documents needed to apply for your WorkSafe CN High Risk Work Licence.

To enrol in the CN crane course in Victoria, you must meet the following selection criteria:

• Age: Be 18 years or older
• Language, Literacy, Numeracy and Digital (LLND) skills: You must be able to use English and maths for safety purposes including reading, writing, and communicating in a training and worksite environment. All students complete an LLND skills assessment prior to enrolment (or discuss their LLND capability with us to confirm suitability)
• Health and fitness: Be in good health and physical condition appropriate for operating heavy machinery in an active worksite environment
• Residency: Reside in Victoria, or hold valid reasons for applying for a Victorian WorkSafe licence
• Visa: Hold a valid visa to study in Australia if you are not an Australian or New Zealand citizen or permanent resident

Not sure if you’re eligible?

We recommend reviewing the sample course documents before committing to enrolment:

• LLND Assessment: complete the sample to gauge your suitability
• Learner Guide sample pages: review the crane safety procedures covered in the course
• Activity Book sample pages: attempt the activity pages to test your readiness

If you have specific learning needs, a disability, limitations, language support requirements, wellness concerns or any other concerns about course suitability, please contact us before enrolling. We are committed to inclusive training and will work with you to find the right support.

Individual / Private Booking: $2,200 per student A deposit of $1,499 is required to secure your place, with the remaining balance of $701 due on Day 1 of the face-to-face training.

Company Booking – 1 to 3 students: $2,200 per student

Company Booking – 4 or more students: $2,100 per student

All pricing covers 4 days of face-to-face training plus pre-learning course materials.

WorkSafe licence fee: The licence application fee is a separate government fee paid directly via the MyWorkSafe portal or at an Australia Post outlet after you have successfully completed your assessment. This fee is set by WorkSafe Victoria and is not included in the course fee.

For full details on refunds, payment options, and financial information, refer to the documents in the Resources tab on this page.

To make the most of your CN crane training days, please bring:

• Current photo ID – required for enrolment verification and again on the licence assessment day(s).
• Completed activity book – to be finished as part of your pre-study before attending
• Appropriate work attire: work pants, work shirt, and steel cap safety shoes (steel caps are required for this course)
• PPE: High-vis clothing and a hard hat are provided, you are welcome to bring your own hard hat if preferred

Go Workplace Training has been delivering WorkSafe-approved high-risk work licence training for over 20 years. We are one of Victoria’s most experienced RTOs in this space, with a proven track record across crane, dogging, rigging, forklift, and EWP licensing.

What sets us apart:

• WorkSafe-approved – our courses meet WorkSafe Victoria’s High Risk Work Licence requirements
• Nationally recognised – your course is valid across all Australian states and territories
• Experienced trainers – our instructors are qualified assessors with real-world crane operation backgrounds
• Purpose-built facilities – our Dandenong South site includes operational non-slewing mobile cranes and a dedicated driving/manoeuvring area for practical assessments
• Flexible pricing options – individual and company group rates available
• Inclusive training environment – we welcome students with diverse learning needs and will work with you on appropriate support
• Comprehensive pre-study materials – learner guides, activity books, and LLND resources included

Whether you’re an individual operator getting your CN licence for the first time, or a business sending a team through crane operator training in Victoria, Go Workplace Training has the experience, facilities, and capacity to get it done.

The CN licence opens employment opportunities across a wide range of industries throughout Victoria and nationally. Non-slewing mobile cranes, particularly Franna and pick-and-carry cranes, are used across virtually every sector of the built environment.

Industries where CN crane operators are in demand:

• Commercial and residential construction – Franna cranes are a staple of mid-rise and high-rise building sites across Melbourne
• Civil construction and infrastructure – road projects, bridge construction, and public infrastructure works
• Industrial and manufacturing – plant and equipment installation and maintenance
• Mining and resources – material handling and equipment positioning on mine sites across regional Victoria and interstate
• Transport and logistics – reach stacker operation in ports, freight terminals, and container yards
• Warehousing and heavy industry – non-slewing telehandler operation in large-scale storage and distribution environments
• Utilities and energy–  infrastructure maintenance, power line works, and renewable energy construction

Licensed CN crane operators are in consistent demand on Victorian worksites. The Franna crane in particular is one of the most frequently requested pieces of equipment, and operators without a current licence are routinely turned away from site. Getting your CN crane course done in Melbourne puts you in a strong position for ongoing site work.

For detailed information about the course, unit requirements, and assessment outcomes:

1. Unit of Competency – full unit requirements, elements, and performance criteria on training.gov.au
2. Course Information Document – course structure, delivery method, and assessment overview
3. Resources Tab – fee schedules, refund policy, complaints procedures, student support services, and pre-enrolment documents
4. Contact Us – speak directly with our team about enrolment, eligibility, pricing, or scheduling

Our CN crane training takes place at our dedicated facility in Dandenong South, Melbourne, equipped with operational non-slewing mobile cranes including articulated Franna cranes, and a purpose-built driving course on private property for practical manoeuvring assessments.

Students complete their practical training and WorkSafe licence assessment on-site under the supervision of qualified trainers and WorkSafe-approved assessors. The environment is designed to replicate real worksite conditions so that participants are genuinely prepared for post-licence employment.

The Dandenong South facility is located at 16 Kitchen Road, with easy access from the Monash Freeway (M1) and Princes Highway is one of the most accessible crane training locations in Melbourne’s south-east.